What sizes does Peter Lewis Paints Lime Fresco come in?
15 Kilograms.
What is the coverage of Peter Lewis Paints Lime Fresco?
The base coat of Peter Lewis Paints Lime Fresco will cover approximately 6m² per kg applying at a thickness of approximately 1mm to 2mm This will vary upon application method, as well as factors such as porosity, surface texture and wastage rates. Final skim coats will cover up to 15m² per kg.
All coverage recommendations should only be used as a guide, as it is truly dependent on the substrate below. Please contact us for more information regarding the coverage of our products.
What is the drying time for Peter Lewis Paints Lime Fresco?
Peter Lewis Paints Natural Lime Fresco is touch dry after 1 hour, however please allow 24 hours between coats. Despite this, the hardness of the lime Fresco is obtained through the combination of lime and marble dust, whereby the hardness occurs upon contact with the air.
All drying recommendations should only be used as a guide, as it is truly dependent on thickness of application, the substrate below and weather conditions. Please contact us for more information regarding the drying time of our products.
What surfaces can I apply Peter Lewis Paints natural Lime Fresco to?
Peter Lewis Paints Lime Fresco can be applied to masonry, previously painted surfaces, plaster and plasterboard. If in doubt about the surface suitability, first use our Lime Proof Undercoat according to the label instructions.
If applying to any other surface, please contact us before use.
What preparation is needed for the surface before applying Lime Fresco?
New and unpainted substrates: Substrates should always be clean and free of loose material, grease, oil, dirt and mould. Surfaces must be wiped down using a lightly dampened cloth before applying. On surfaces that are bare such as new unpainted plasterboard, render, brick or timber, prepare the surface using our Lime Proof Undercoat. On fresh set plaster you must allow the plaster to fully cure and then apply one coat of Peter Lewis Paints Mineral Silicate Primer, by brush or roller. Allow 2 hours drying time, or until dry completely. Then apply two coats of Peter Lewis Paints Lime Fresco.
Previously painted substrates: Where painted surfaces are loose, peeling or flaking, these surfaces must be made sound first, by removing loose paint, filling any cracks and nail holes with a suitable filler. Then it should be prepared and dusted off. All repaired areas to be spot primed with our Lime Proof Undercoat, allowed to dry, then apply one coat to the entire area. It should be touch dry in 2 hours, however, allow 6 hours dry time.
For any other queries about Lime Fresco preparation, please contact us.
What is the best weather to apply Lime Fresco?
Peter Lewis Paints eco-friendly Lime Fresco should not be applied in high humidity, or when the surface temperature is below 10°C or above 30°C.
For any other queries about Lime Fresco application please contact us.
How many coats of Peter Lewis Paints Lime Fresco do I need?
Two coats are needed of Peter Lewis Paints Lime Fresco. Please read the FAQ labelled ‘How do I apply Peter Lewis Paints Lime Fresco?’ for exact application instructions.
However, this recommendation should only be used as a guide, as it is truly dependent on the substrate below. Please contact us for more information regarding the application and coverage of our products.
How do I apply Peter Lewis Paints Lime Fresco?
Apply two coats of Peter Lewis Paints Lime Fresco with a spatula or trowel. The first base coat should be under 1mm thick and further coats should be applied as thinly and as evenly as possible. Always keep a wet edge while applying, filling the unevenness of the previous coat. During the second coat, as the Peter Lewis Paints Lime Fresco is drying, you can start polishing, with a flexible mark-free stainless steel trowel or spatula to give you the desired appearance. If you desire a polished plaster finish, you can apply the Peter Lewis Paints Stucco Wax. Peter Lewis Paints Lime Fresco should not be applied in high humidity, or when the surface temperature is below 10°C or above 30°C.
Are there any safety cautions with Peter Lewis Paints Lime Fresco?
Due to the Lime based nature of Peter Lewis Paints natural Lime Fresco, if contact with the eyes occurs, rinse with running water and seek help if irritation persists. Avoid long periods of skin contact. If swallowed do not induce vomiting. Give a glass of water and seek medical assistance or contact the Poison Information Centre (13 11 26).
Please refer to the Safety Data Sheet for more safety information.
Can I apply Peter Lewis Paints Lime Fresco over existing paint?
Yes, Peter Lewis Paints eco-friendly Lime Fresco can be applied over existing paint, however, where painted surfaces are loose, peeling or flaking, these surfaces must be made sound first, by removing loose paint, filling any cracks and nail holes with a suitable filler. Then it should be prepared and dusted off. All repaired areas to be spot primed with our Lime Proof Undercoat, allowed to dry, then apply one coat to the entire area. It should be touch dry in 2 hours, however, allow 6 hours dry time. After this process the surface is ready for Lime Fresco application.
For any other queries about Lime Fresco application please contact us.
Can you recommend any applicators to apply Peter Lewis Paints Lime Fresco?
Yes, we have applicators around NSW that are experienced using our product that we recommend to our clients. Please contact us to find out more.
